What is Materials Testing?

Discover where and how materials testing can be applied to measure the mechanical/physical properties of materials

Three point bend test of plastic on the TA.HDplus Texture Analyser

Materials testing is a popular and well known field of measurement to obtain physical and mechanical properties of materials from powders or raw materials, components and composite finished products. It is a wide-ranging field offering force and distance (stress/strain) measurement solutions from the tension of a shoelace to the crush resistance of cardboard packaging, the actuation force of switches to the measurement of friction between two materials. Materials testing instruments such as theTA.HDplusCTexture Analyserare found imperative in quality control and production environments to maintain product quality and performance specifications and also in laboratory or R&D locations where it is important to assess the effects on materials due to for example, change of supplier, process or temperature.

How does a Materials Testing Machine work?

The arm of a Materials Testing Machine/Texture Analyser instrument holds a load cell – a highly accurate strain gauge that allows the measurement of forces up to 750kg. The arm is moved up and down via the control ofExponent Connect在选择软件可编程移动speeds and moved to chosen distances or the instruments can operate as pre-programmed stand-alone units. During testing, stress and strain data from the compression/tension of a sample are recorded and analysed. Data is usually displayed as graphs which are then analysed and relevant parameters shown in a spreadsheet. These parameters will have been chosen as the important material characteristics to measure in order to determine whether the tested material is fit for purpose or complies with a determined standard value. Measurement values which fall outside of a quality boundary could result in physical failure during use or have quality changes during storage which could have safety implications and ultimately damage the reputation of the product and/or company.

The full range of Texture Analysers for any testing application

What industries can materials testing machines be used in?

Materials and therefore the requirement for materials testing are everywhere in industries ranging from plastics, medical, paper and cardboard, leather and textiles, automotive, medical devices, building materials and the electronics industry.

What typical properties can materials testing instruments measure?


Actuation Forces

Burst Strength





Peel Strength/Seal Strength


Tensile Strength/Breaking Strength/Elongation

The TA.HDplusC/ TA.XTplusC100Materials Testers are experts in the measurement of all of these properties and many more, with ASTM Standard tests built into the software or using the flexibility of empirical or imitative force measurements. High accuracy and reliability are the instruments’ forte, with forces of up to 750kgf and distance resolutions of half a micron available. Testing is easy and repeatable as test settings are automatically loaded and additional data such as audio and visual can be recorded to help with analysis, such as in the event of a fracture.

At their most simplistic form, these tests all have one of two things in common – a test in either tension or compression. A multitude of probes and fixtures are available that attach to the Materials Tester for the support of the material or for specific application of force/deformation to the material.See materials testing attachments

Some Typical Fixtures used for Materials Testing

In compression mode, a number of tests types are available covering和雷竞技一样的软件 ,extrusion,和雷竞技一样的软件有哪些 ,雷电电竞app , with a few typical examples shown below.

In many cases, non-standard applications can be accommodated through the design of a special rig, fixture or clamping device to hold the particular sample without needing to modify the testing machine itself.

Materials Testing and Standard Methods

AStandard Test Methodis a definitive procedure that produces a test result. In order to ensure accurate and relevant test results, a standard test method is explicit, unambiguous, and experimentally feasible, as well as effective and reproducible. A standard test method can be considered an experiment that determines one or more characteristics of a given sample and the detail of the test method is usually as a result of creation from a number of experts in that measurement field. Within the materials testing industry, for example, there are an enormous number of standard methods (e.g. ASTM, ISO) that have been developed to measure specific sample characteristics.

Typical examples of those that use Texture Analysers or Materials Testing equipment are:

• ASTM D882-02: Tensile test of thin plastic sheeting (thickness<1mm)

• EN 1944:1996 - Self Adhesive Tapes - Measurement of Unwind Adhesion at Low Speed

When reporting results in an academic paper or industrial report these standard methods will have been adhered to for the collection of the results and are more globally understood by others using the same standard methods. It is for this reason that standard methods have their place in the laboratory.

A large number of companies use one of a suite ofTexture Analysersto calculate fundamental parameters which take into account the geometry and dimensions of the sample as well as the specifics of the test set up along with the relevant engineering equations. This type of testing allows easier comparison of different samples and comparison with literature data, but does require more sophisticated analysis to convert forces to stress and distances to strain.

Standard Method Data Analysis and Engineering Calculations

If fundamental testing is key to your operation and you are unaltered in your preference for this means of testing then standard engineering calculations are built intoExponentsoftware for quick calculation of specific moduli, stresses, strains, strengths and energies which are particularly suited to materials testing applications. Each calculation is designed to be used with a very specific test setup (for example, cuboid three point bend testing) as the specific equations required for analysis depend on the sample and test geometry.

Types of materials testing measurement and their analysis possibilities

Regardless of whether the test is performed in compression or tension, a resulting curve can be analysed to obtain the following typical parameters:

Strain rate; Young’s Modulus; Tangent, chord and secant modulus; Resilience; Yield stress; Strain to yield; x% proof stress; Maximum stress; Strain at maximum stress; Energy to maximum stress; Breaking strain; Hysteresis %; Energy to failure.See the full list of parameters

Whilst the equipment can provide a simple and flexible empirical or imitative solution it is also able to offer the traditional measurements well established within the materials industry mentioned above. Over the years, Stable Micro Systems has incorporated a large number of test procedures and analysis methods suitable to obtain fundamental materials parameters that could be used across a wide range of industries. WithinExponentsoftware all of the above analysis options can be accessed according to the test type:

Illustration of user choosing test type in Exponent Software

Why change from the Standard Method approach for Materials Testing?

Texture Analysersare very often used for quality control of irregular products by the use of empirical measurements. The force required to crush a tablet or the distance a biscuit bends before it snaps are invaluable pieces of information to manufacturers looking to develop new products or ensuring products perform correctly during spot checks. This type of test is ideal for products that have an unusual geometry, but it is also useful for testing more complicated systems, such as the combination of a product and its packaging (a box of eggs, the force to open a ring pull can or a yoghurt in its pot) with the added benefit of time saved by allowing a product to be tested straight off the supply line. Measurements of this nature do not fall within the specific (and therefore restricted) dimension criteria of fundamental materials testing and present classic examples of where empirical testing has its place.

In the food industry, for example, there are far fewer standard methods for physical property measurement. However, you may already be following one of few specific Standard methods to test your samples, e.g. ISO Gelatine Bloom Strength, AACC Bread Freshness, AACC Pasta Firmness, ASTM Petroleum Wax Firmness, ASTM Adhesive Peel Strength.

The limitations of applying standards is that their biggest advantage (of being specific) can be a major disadvantage (or restriction) to the measurement. All too often, operators are forced to use a standard method to measure a property of their product when:

• The property that the standard method measures is not the most important, or interesting, measurement that could be performed on the sample, or

• The sample preparation procedure may be difficult (or impossible) to conform with given the sample to be tested is different to the sample for which the test method was developed.

A well-written test method is important. However, even more important is choosing a method of measuring the correct property or characteristic. Not all tests and measurements are equally useful: usually a test result is used to predict or imply suitability for a certain purpose. However, it would seem more important to measure the most important characteristics of a product than to follow a seemingly pointless standard method that does not ideally characterise the product.

If you’re not bound by any existing constraints and are looking for the most simple testing solution, sometimes the easiest approach is to set up a test that closely imitates the way the product is evaluated in real life. This is called an ‘Imitative Test’. This type of test usually also makes data interpretation easier for you to understand.

The methods used for physical testing should measure the desired characteristics necessary to monitor the process, but need not always be comparable with other laboratories, where different criteria may be important. Where international comparison is important it is essential that methodologies be standardised. This would include all aspects of the testing procedure and this is an area of which the reference methods are primarily directed.

In contrast, where direct measurements are being made of the physical properties of a product, the experimental methodologies should not be constrained by reference methods. Instead, researchers are encouraged to develop and use methodologies that enhance the precision and accuracy of testing methods and lead to an understanding of the basic mechanisms. It is likely that new understanding will lead eventually to methods that more closely predict consumer assessment of product characteristics. The Stable Micro Systems range of Texture Analysers provide the flexibility of testing principles (e.g. compression, penetration, tension, extrusion, etc.) and the endless option of probes, fixtures and data analysis techniques within the software for texture analysis and fully customisable test settings.

Whilst standard methods are particularly useful for traditional material forms that have not changed over the decades and are fully accepted there lies another world where creativity has taken off into new materials and material forms for which these standard methods cannot be applied. One example of such an issue is in the field of pharmaceutical development. Traditional methods are well established for the testing of tablets, gels, suppositories, medicated liquids that are manufactured in their traditional form, however, innovative dosage forms have been developed such as disintegrating films, capsules, chewable pastilles for which there is no standard method to apply for the measurement of their physical (or textural) characteristics. Alternative testing methods that accommodate the testing of samples of varying types and dimensions and the range of additional material characteristics which can be measured, are required.

Not only are new non-standard methods viable where sample dimensions cannot be prepared according to the standard but also where the operator may wish to modify the test parameters (such as the test speed) to more closely mimic the situation under which the sample is to be typically used.

Here is a summary of typical texture analysis/materials testing tests that can beperformed on materialsorwatch this videoto see the highlights.

We use cookies
Please note this website uses cookies to give you the best experience.
By continuing to browse this site you give consent for cookies to be used.Find out more